Mitsubishi Electric PLA-RP50 Wartungshandbuch PDF herunterladen (Seite 32)

SPECIAL FUNCTION

11-1. HOW TO PERFORM THE UP/DOWN OPERATION OF THE AIR INTAKE GRILLE

11-1-1. Setting up the lowering distance of air intake grille

Dip SW 22 Dip SW 2

Lowering distance

(Rough indication

of the ceiling height)

1.2m

(~ 2.4m)

2.0m

(2.8m ~ 3.2m)

2.8m

(3.6m ~ 4.0m)

3.6m

(4.4m ~ 4.8m)

1.2m

(~ 2.4m)

2.0m

(2.8m ~ 3.2m)

2.8m

(3.6m ~ 4.0m)

3.6m

(4.4m ~ 4.8m)

1.6m

(2.4m ~ 2.8m)

2.4m

(3.2m ~ 3.6m)

3.2m

(4.0m ~ 4.4m)

4.0m

(4.8m ~ 5.2m)

1.6m

(2.4m ~ 2.8m)

2.4m

(3.2m ~ 3.6m)

3.2m

(4.0m ~ 4.4m)

4.0m

(4.8m ~ 5.2m)

Lowering distance

(Rough indication

of the ceiling height)

Initial setting

SW22

(Lowering distance)

SW22

(Lowering distance)

Lowering distance

(Rough indication

of the ceiling height)

Lowering distance

(Rough indication

of the ceiling height)

SW2

(Lowering distance)

SW2

(Lowering distance)

Screws

Unit

Control board of

the decorative

panel

SW 22 or SW2

Decorative

panel

Cover for

Electric Box of

the decorative

panel

You can set up 8 different stages of lowering distance for

the air intake grille according to the set up location if desired.

* As a factory default, the decorative panel will automatically

stop at 1.6 m from the ceiling surface. The distance is a

rough indication, check by actually lowering it.

1) Take the cover off the electric box of the decorative panel. (2 screws)

2) Set up the dip switches of SW22 or SW2 on the control board of the

decorative panel as followed.

3) Put the cover back on the electric box of the decorarive panel.

* Airflow outreach distance is different depending on indoor units and

air volume (ceiling height), so airflow may not reach the indicated

ceiling height as shown in the above table.

* Airflow outreach distance is different depending on indoor units and

air volume (ceiling height), so airflow may not reach the indicated

ceiling height as shown in the above table.

Initial setting

The black square (■) indicates a switch position. The black square (■) indicates a switch position.

1) Ensure that the air-conditioner is not running.

2) Press the "Down" button to lower the air intake grille.

* By default, the air intake grille will automatically stop at a lowering distance of 1.6 m from the ceiling level.

The distance can be changed to 1.2 m, 2.0 m, 2.4 m, 2.8 m, 3.2 m, 3.6 m and 4.0 m. These should be used

only as a guide. You should lower the air intake grille yourself to check the exact distance.

* When you want to stop the air intake grille while it is lowering, press the "Stop" or "Up" button on the remote

controller to stop at that position.

3) Remove the filter or air intake grille and clean them.

4) Attach the filter and air intake grille.

5) Press the "Up" button on the remote controller to put the air intake grille in place.

* If the air intake grille is not placed in the correct position at a time, the operation is automatically retried.

* When you want to stop the air intake grille while it is rising, press the "Stop" or "Down" button on the remote controller

to stop at that position.

Wireless remote

controller for

Automatic Filter

Elevation Panel

Ensure that the air-conditioner is not running.

• Otherwise, it may cause an injury or a failure.

Warning:

11-1-2. How to perform the up/down operation using wireless remote controller

Downloaded from AC-Manual.com Manuals

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 43 44

Kommentare zu diesen Handbüchern

Keine Kommentare

Mitsubishi Electric PLA-RP50 Wartungshandbuch Seite 32

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Split-System-Klimaanlagen Mitsubishi Electric PLA-RP50